MS POLIA

pdf

ISONEM MS POLIA is a polymer with excellent properties produced in the latest technology. It is ready to use, water-based, polymer-based, UV resistant and elastic structure. It is used as insulation material on the terrace, roofs, concrete, screed, plaster, wood, metal surfaces and surfaces which were applied spray polyurethane thermal insulation. Workmanship is easy and fast.

TECHNICAL SPECIFICATIONS

Density (25°C, g/mL): 1,30 ± 0,10

pH (25°C): 7,0 – 9,0

Viscosity (25°C, mPa.s): 16000 - 18000

Solid content (% Weight): 70 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking ≥ 0,8, with trafficking 1,5 N/mm²

Permeability to water vapour (m): 5 ≤  SD ≤ 50 CLASS II

Solvent: Water

 
Documents of the ProductDocuments of the Product

·  Waterproofing of roofs.

· Facades

· Roofs, woods, decks

· On old-based bitumen problematic insulation

· Shingle surfaces

Surface Preparation: The surface to be insulated must be clean and dry. Any dirt, mud, rust or oil, must be removed on the surface. It is not used in areas salt efflorescence or places on water flow from the negative side. All cracks and holes should be repaired with ISONEM M 03. Especially in large spans and thermally insulated floors, we recommend applying 45 g/m2 of insulating mesh on floors which are possible to crack.

If there is dilatation in the area to be insulated, dilatation insulation should be made with ISONEM A4 elastic filling and then insulation should be started.Before ISONEM MS POLIA application, ISONEM UNIVERSAL PRIMER (1: 7 diluted with water - 1 part primer, 7 part water) insulation and paint primer should be applied one layer with 100 - 200 g/m2 consumption and then is allowed to dry for 4 hours. The main application should be started after the primer application is waited to dry between 4-6 hours. In steel/metal surfaces, the surfaced should be primed with ISONEM ANTI RUST PRIMER (Anticorrosive primer), consumption of 0,250 - 0,350 kg/m2.

Application Method: ISONEM MS POLIA is ready to use. It should be mixed homogeneously after opening the cover and before application. ISONEM MS POLIA is applied on the primed surface in two layers without dilution at 4 hours intervals. Application should not be made under 5 ° C or on wet and frozen floors. It should be checked whether the correct and sufficient slope is given, especially in applications performed on flat roofs. Care should be taken to ensure that sufficient water drain is available and that there is no ponding of water on the roof or terrace.

CONSUMPTION: 0,8 - 1,0 kg / m² (two layers application)

PAINTABLE (COVERAGE) AREA): 5 kg: min. 5 m2/bucket (two layers application)

10 kg: min. 10 m2/bucket (two layers application)

18 kg: min. 18 m2/bucket (two layers application)

PACKAGING: 5,10, 18 kg in PP Bucket
 
COLOR: All requested can be produced in colors
 
STORAGE CONDITIONS / SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages
...
ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos ISONEM MS POLIA Application Photos
Share this product:
x