MD 28

pdf

It is a cement-based, two-component, crack bridging capacity and walkable an insulating product having high abrasion resistance. It is applied by brush, has high elasticity. It closes the capillary and shrinkage cracks on the applied surface. It has high adherence. It adheres perfectly to surfaces like concrete, plaster, screed, etc. and does not get removed by time. It is resistant to outdoor weather conditions, UV, mechanical impacts and abrasion. It is water based, acrylic emulsion and cement based, two components.

TECHNICAL SPECIFICATIONS

Density B comp. (25°C, g/mL): 0,90 ± 0,10

pH B comp. (25°C): 7,0 – 9,0

Viscosity B comp. (25°C, mPa.s): 9000 - 12000

Solid content B comp. (% Weight): 48 ± 2

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking  ≥ 0,8, with trafficking 1,5 N/mm²

Permeability to water vapour (m): 5 ≤  SD ≤ 50 CLASS II

Pot life (23°C): 30 – 40 minutes

Solvent: Water

 
Documents of the ProductDocuments of the Product

· Positive insulation of walls and floors,

· Insulation of concrete, plaster, and screed,

· Balcony, terrace, swimming pools

· External curtain wall insulation,

· Precast and prefabricated elements, roofs.

Surface preparation: All surfaces should be cleaned from foreign objects like oil, dust, dirt, etc. before the application. The surface must be clean and moist. If there are any segregations, voids or need for repair on the surface, they should be filled with ISONEM M 03 elastic mortar. If there are surfaces with adhesion problems, they should be primed with adherence enhancer ISONEM D 10 LATEX and ISONEM MD 28 should be applied while the surface is slightly sticky and before it is completely dry.

Preparation of the mixture: ISONEM MD 28 consists of two components. The first part is component A consisting of powder polymer and hardener and the second component is liquid component B consisting of liquid polymer. B component (10 kg) in liquid form is placed in a clean, sufficiently large container. A component (20 kg) of powder is slowly added to the continuous mixing liquid with the aid of a mixer and gently mixed so that no lumps remain. Mixing should be continued for 5 minutes. At the end of the mixing, a homogenous, brushable mortar is obtained.

Application method: ISONEM MD 28 should be applied in 3 coats. The application process should be perpendicular layers to each other, homogeneously and smoothly with the help of a brush. The wet film thickness should not exceed 1 mm at one layer. It should be waited a min. of 4 hours between the coats and it should not be interrupted for more than 24 hours. The application should not be done in extreme heat or frost, it should be done in the morning or evening cool. It is recommended to use with grout detail in chamfer applications. Tools used should be cleaned with water at the end of the application.

CONSUMPTION2 - 3 kg/m² (three layers application) 

PAINTABLE (COVERAGE) AREA):10 - 15 m² /1 set

COLOR: Greenish gray

PACKING30 kg set, Component A 20 kg powder craft bag + B Component 10 kg liquid PE drum

STORAGE24 months from date of production if stored in original, unopened, undamaged packages. Store tightly closed in a dry and cool place

...
ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos ISONEM MD 28 Application Photos
Share this product:
x