M 35

pdf

It is a single component cement-based super crystalline waterproofing product. It provides insulation deeply by way of applying to concrete surfaces from both negative and positive sides. It reacts with lime particles thanks to inside super gels, produces crystals, and penetrates in-depth to the structure of concrete. It can be applied to new concrete surfaces. It slows down the hydration process on the surface it is applied to and reduces shrinkage crack formation. In addition to waterproofing, it protects concrete against corrosion and diluted chemicals.

 

TECHNICAL SPECIFICATIONS

pH (25°C): 12.0 – 13.0

Water transmission rate (kg/ m2. h0,5): < 0,1 CLASS W3

Adhesion strength by pull-off test (N/mm2): Crack bridging flexible systems without trafficking  ≥ 0.8, with trafficking 1.5 N/mm²

Permeability to water vapour (m): 5 ≤  SD ≤ 50 CLASS II

Solvent: Water

 

 
Documents of the ProductDocuments of the Product

· Waterproofing of horizontal/vertical floors and walls, internally or externally,

· Water tank, wastewater, and other water tanks,

· In concrete surfaces exposed to seawater,

· In the basement floor and underground insulation,

· In the insulation of the basic curtain walls internally or externally,

· Irrigation channels and tunnel or dam structures.

Surface preparation: The application surfaces should be dampened previously. The dampening process is made until the surface is saturated 2 hours before starting the application. This process is not necessary if the surface is damp or wet beforehand. The application surfaces should be cleaned from particles such as oil, dirt, mud. If there are segregation, concrete disturbances, and holes, firstly these should be repaired with ISONEM M 03 Elastic Repair Mortar with applying ISONEM D 10 LATEX. Dilatations should be filled with ISONEM A4 elastic filler in advance. The mixture should be prepared after the surface is ready.

Preparation of the mixture: 7 L of clean water is poured into a suitable container. While continuous mixing ISONEM M 35 (20 kg) should be poured slowly and stirring should be continued for 5 minutes. If possible, mix with a 400 rpm drill and mixer. When the mixing process is completed, it is obtained a paint-like mortar that can be applied with a homogeneous brush.

Application method: The application is applied in three coats by brush, wait for 4 hours between the layers. The application should be applied in opposite directions on each layer. The surface should completely close when it is applied to the surface by three layers. The application should not be done in frost and extreme temperatures and should be carried out in cool environments during the evening or early morning. If a frost occurs in cold areas, the floor or wall should be pre-watered with hot water. If the surface will not be covered and the plaster will not be applied after The M 35 application, the application surfaces should be humidified at 48 hours intervals. This process accelerates the curing process and provides more successful insulation.

CONSUMPTION: 2 - 3 kg/m² (three layers application)

PAINTABLE (COVERAGE) AREA6 - 10 m²/ Craft bag

PACKING: 20 KG craft bag

SHELF LIFE: 24 months from date of production if stored in original, unopened, undamaged packages.

STORAGE CONDITIONS: Store tightly closed in a dry and cool place.

 

 
...
ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos ISONEM M 35 Application Photos
Share this product:
x