ISONEM M 03
I NEED MORE INFORMATION
5 + 4

ISONEM M 03

Polymer Modified Repair Mortar

 

ISONEM M 03 is a cementitious, polymer modified, fiber reinforced, one component repair mortar for horizontal, vertical and overhead applications. ISONEM 03 can also be used in combination with ISONEM EP epoxy bonding agent for trafficed repairs. USES: •Fair faced concrete repairs •Repairs of wall and ceiling •Preparation of substrates before tile applications
CHARACTERISTICS / ADVANTAGES: •One component, it can be mixed with water only •Adjustable consistency •Because of its thixotropic behavior, suitable for vertical applications •Applicable in a layer up to 100 mm thickness •Non corrosive, non-toxic •Suitable for wet spray method
TECHNICAL PROPERTIES: •Appearance / Colour: Grey powder •Chemical Base: Cementitious mortar modified with polymers and fiber materials. •Density Fresh mortar: 2,0 ± 0,1 kg/l (at +20°C) •Grading Dmax: 1.3 mm •Layer Thickness: 10 mm min. / 100 mm max. 

Documents of the ProductDocuments of the Product
Usage AreasUsage Areas
Application TypeApplication Type

•Application temperature: between + 5°C and +30°C •Potlife: ~ 1 hour (at +20°C) •Compressive Strength: (21±2) ºC and (60±10) % r.h. 7 days; 45 N/mm2 28 days; 55 N/mm2 •Flexural Strength: (21±2) ºC and (60±10) % r.h. 7 days, ~ 7,5 N/mm2 28 days, ~ 9,8 N/mm2 •Bond Strength: > 1,5 N/mm
APPLICATION PROCEDURE SUBSTRATE QUALITY / PREPARATION: The concrete must be premoistured, structurally sound, clean and free from dust,dirt, oil, grease, loose or friable particles other contaminants (such as paint etc.). ISONEM D10 LATEX Super bonding layer is applied in order to increase adhesion and improve impermeability by brush and then the mortar is applied wet on wet to the surface.
APPLICATION CONDITIONS / LIMITATIONS: •Substrate Temperature +5°C min. / +30°C max. •Ambient Temperature +5°C min. / +30°C max.
APPLICATION INSTRUCTIONS MIXING RATIO: For 20 kg bag, 4,0 liter water must be used. Water/Powder ratio must be 0,20–0,22 by weight Water/Powder= 1: 4,5 – 5,0 by weight MIXING: Pour water in correct proportion into a suitable mixing vessel. Add powder, whilst stirring slowly. To avoid entraining too much air mix mechanically for at least 3 minutes, using low speed electric stirrer (max. 500 rpm) in order to maintain a homogeneous mortar.
APPLICATION METHOD / TOOLS: ISONEM M 03 can be applied by wet spray equipment with spatula or trowel. The mortar is applied wet on wet to the ISONEM D10 LATEX bonding layer. For thickness grater than 100 mm, ISONEM M 03 must be applied in several layers. As soon as the mortar has started to set it can be smoothed by wooden or synthetic float or a styrofoam block. For very fine surface finish, the application of ISONEM M 03–T is advised.
CLEANING OF TOOLS: Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed. CURING: The mortar must be cured with suitable curing materials to prevent premature drying out of the mortar or standard curing methods are recommended. Keep it moist if exposed to strong sunshine or wind.
NOTES ON APPLICATION / LIMITATIONS: •Please do not use more water than advised. •Do not use the product below the allowed min. temperature so that the material completes the setting. The setting is slowed down under low temperatures and speeded up under high temperatures. Workability period also varies inversely depending on the temperature

Consumption and Suggestions

CONSUMPTION: For one coat of 1 mm ~2,00 kg/m2 powder material is required. Material consumption depends on substrate conditions and application method.
PACKAGE: 20 kg craft bag
HEALTH AND SAFETY INFORMATION: For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Material Safety Data Sheet containing physical, ecological, toxicological and other safetyrelated data. Polymer Modified Repair Mortar
STORAGE CONDITIONS/SHELF LIFE: 24 months from date of production if stored properly in unopened and undamaged original sealed containers at temperatures between +5°C to +35°C at dry conditions. Protect from excessive temperature and frost.

Application Photos
ISONEM M 03 Application Photos
ISONEM M 03 Application Photos
ISONEM M 03 Application Photos
ISONEM M 03 Application Photos
ISONEM M 03 Application Photos
ISONEM M 03 Application Photos
ISONEM M 03 Application Photos
ISONEM M 03 Application Photos
Share this product: