ISONEM POLYASPARTIC FLOOR
Polyaspartic Floor Covering
Isonem Polyaspartic Floor is a two-component, high performance, user and environmentally friendly super-fast flooring material featuring very fast curing. Due to the low application times of new coats, the applied floors can be opened to service after about 1 - 2 hours. It has excellent UV resistance, does not yellow, does not lose its brightness. It is highly resistant to chemicals and its chemical resistance is 4 times higher than epoxy-based coatings. It is hygienic, creates a smooth surface and its stain resistance is quite high. It has an extremely high mechanical strength, it can be used comfortably in the areas open to vehicle traffic, it cannot be cracked, scratched or crushed. It has high adhesion strength. It has excellent adhesion to concrete and metal and it does not peel. The application is easy and maintenance costs are very low.
FEATURES / ADVANTAGES:
- User and environment friendly, free of any volatile components (VOC-solvent)
- Easy and fast to apply. It can be opened to service in a few hours.
- Excellent resistance to environmental conditions. No yellowing due to its UV resistance.
- Hygienic, stain-resistant, easy to clean.
- High mechanical strength.
- High adhesion strength, no peeling off from the surface.
- Low maintenance costs.
Product structure: Two-component, polyaspartic system
Color: Transparent or in desired standard colors
Density (25°C, g/mL): 1.00 gr/ml ± 0,10
Viscosity (25°C, mPa.s): 1000 – 2000
Brightness (with an angel of 85°): > 60, CLASS G1
Dust dry time (25°C): 15 – 20 minutes
Hard dry time (25°C): Approximately half an hour
Through-dry time (25°C): 1 - 2 hours
Mixture life: Temperature Time
+25°C ~30 minutes
Time of use: Temperature Time
+30°C ~15 minutes
+20°C ~20 minutes
Mixture ratio : 1/1 (by weight)
Manufacturing plants, storage facilities, distribution centers, food processing plants, textile factories, cold storage / freezers, beverage processing, chemical processing, multi-storey car parks, aircraft hangars, parking places, transportation terminals, vehicle maintenance areas, office buildings, cafes and restaurants, shopping centers, schools, education facilities, chemical fields, laboratories
The application surfaces must be dry, clean and free from any dirt, oil, dust and surface wastes.
Preparation of the Mixture
ISONEM POLYASPARTIC FLOOR is supplied in ready-to-use sets according to the mixing ratio. Prepare an amount of mixture to be applied by considering the mixture life. Before starting to mix, make sure that temperatures of the materials are between +15 and +25°C. Stir component A with a 300 – 400 rpm mechanical mixer for 3-4 minutes without dragging air in it. Then, pour the entire component B into component A and make sure that no material is left in component B. Stir component A and B at least for 3 minutes until a homogenous mixture is obtained and consume the prepared mixture within 15 - 30 minutes.
ISONEM POLYASPARTIC FLOOR should be applied with a brush or roller to obtain the desired thickness. The product must be applied in 2 coats for full performance. Let the previous coat reach adhesive dryness before applying the second coat.
WARNING: During and after the application, protect from external factors such as rain, water, mechanical impacts, etc. for 24 hours.
CONSUMPTION : Depending on the surface, 0.150 – 0.300 kg/m² (single coat application)
PACKAGING : 5 kg set - Component A, 2,5 kg tin can +
Component B, 2,5 kg tin can (hardener)
STORAGE : 24 months in the original, unopened package in a cool and dry environment.
Notes: All technical information given in this Product Data Sheet is based on laboratory tests. Actual values may vary due to circumstances beyond our control
Health and Safety Information: Users should refer to the material safety data sheet (MSDS) of the product for information and recommendations on the safe transport, storage and disposal of chemical products, including physical, ecological, toxicological and other safety related information.